Yıl 2018, Cilt 4, Sayı 1, Sayfalar 89 - 101 2018-06-26

LIFE CYCLE COST ANALYSIS IN DETERMINING OPTIMUM PIPE INSULATION THICKNESS WITH AIR GAP FOR DIFFERENT CLIMATE CONDITIONS
FARKLI İKLİM ŞARTLARI İÇİN HAVA BOŞLUKLU OPTİMUM BORU YALITIM KALINLIĞININ BELİRLENMESİNDE YAŞAM DÖNGÜSÜ MALİYET ANALİZİ

Yusuf Başoğul [1]

55 92

This study is about determining air gap, insulation material in pipes between 50 mm and 1000 mm in mechanical installation, and determining optimum insulation thickness, energy saving and payback period in cases where both are being used. For this calculation, life cycle cost analysis containing heating degree day has been used. Even though Afyon province climate conditions have been used as the case study, the study has been expanded for cold, temperate and warm climate conditions. This made it possible to make comparative assessments for insulation thickness, air gap, pipe diameter and heating degree day values. In 50 mm and 1000 mm pipes using air gap, the optimum insulation thickness was reduced by 81% and 39% respectively. It is recommended to use air gap in mild climates and to use insulation in cold climates. When insulation with air gap is applied, optimum insulation thickness is reduced, and in pipes with greater diameter energy cost saving is increased while in pipes with smaller diameter the payback period is reduced.

Bu çalışma mekanik tesisatta 50 mm ile 1000 mm arasındaki borularda hava boşluğu, yalıtım malzemesi ve her ikisinin kullanıldığı durumlardaki optimum yalıtım kalınlığı, enerji tasarrufu ve geri dönüş süresinin belirlenmesi ile ilgilidir. Bu hesaplama için ısıtma derece günler içerikli yaşam döngüsü maliyet analizi kullanılmıştır. Durum çalışması olarak Afyon ili iklim şartları kullanılmasına rağmen çalışma soğuk, ılıman ve sıcak iklim şartları için de genişletilmiştir. Böylece yalıtım kalınlığı, hava boşluğu, boru çapı ve ısıtma derece gün değerlerine göre karşılaştırmalı değerlendirmeler yapılmıştır. Hava boşluğunun kullanıldığı 50 mm ve 1000 mm’lik borularda optimum yalıtım kalınlığı sırasıyla  %81 ve %39 düşmüştür. Ilık iklimlerde hava boşluğunun ve soğuk iklimlerde ise yalıtımın kullanılması tavsiye edilir. Hava boşluklu yalıtım uygulandığında optimum yalıtım kalınlığını düşürmekle birlikte büyük çaplı borularda enerji maliyet tasarrufu artarken küçük çaplı borularda geri dönüş süresi düşmektedir.

  • Kecebas, A., Alkan, M.A. and Bayhan, M., “Thermo-economic analysis of pipe insulation for district heating piping systems”, Applied Thermal Engineering, Vol. 31, 3929–3937, 2011.
  • Mohsen, M.S. and Akash, B.A., “Some prospects of energy saving in buildings”, Energy Conversion and Management, Vol. 42, 1307–1315, 2001.
  • Suman, B.M. and Srivastava, R.K., “Effect of air gap on thermal performance of composite wall section,” Indian Journal of Science and Technology, Vol. 1, 1–4, 2008.
  • Mahlia, T.M.I. and Iqbal, A., “Cost benefits analysis and emission reductions of optimum thickness and air gaps for selected insulation materials for building walls in Maldives”, Energy, Vol. 35, 2242–2250, 2010.
  • Kurt, H., “The usage of airgap in the composite wall for energy saving and air pollution”, Environmental Progress & Sustainable Energy, Vol. 30, 450–458, 2011.
  • Dasdemir, A., “Economical and environmental analysis of the usage of air gap in the composite wall”, Electronic Journal of Machine Technologies, Vol. 8, 49–61, 2011.
  • Ridouane EH, Bianchi MVA. Thermal performance of uninsulated and partially filled wall cavities. ASHRAE Annual Conference Montreal, Quebec, June 25–29, 2011.
  • Mahlia, T.M.I., Ng, H.M., Olofsson, T. and Andriyana, A., “Energy and cost savings of optimal thickness for selected insulation materials and air gaps for building walls in tropical climate”, Energy Education Science and Technology Part A: Energy Science and Research, Vol. 29, 597–610, 2012.
  • Cai, S. and Cremaschi, L. “An experimentally validated model to predict the thermal conductivity of closed-cell pipe insulation systems with moisture”, ASHRAE Conference Paper No: NY-14-C090, ASHRAE Winter Conference, New York, 2014.
  • Faris, S.S., Chaichan, M.T., Sachit, M.F. and Jaleel, J.M., “Simulation and numerical investigation of the effect of air gap thickness on trombe wall system”, International Journal of Application or Innovation in Engineering & Management, Vol. 3, 159-168, 2014.
  • Erturk, M., “A new approach to calculate the energy saving per unit area and emission per person in exterior wall of building using different insulation materials and air gap”, Journal of the Faculty of Engineering and Architecture of Gazi University, Vol. 31, 395–406, 2016.
  • Kayfeci, M., “Determination of energy saving and optimum insulation thicknesses of the heating piping systems for different insulation materials”, Energy and Buildings, Vol. 69, 278–284, 2014.
  • Basogul, Y. and Kecebas. A. “Economic and environmental impacts of insulation in district heating pipelines”, Energy, Vol. 36, 6156–6164, 2011.
  • Kecebas, A., “Determination of optimum insulation thickness in pipe for exergetic life cycle assessment”, Energy Conversion and Management, Vol. 105, 826–35, 2015.
  • Kecebas, A., “Determination of insulation thickness by means of exergy analysis in pipe insulation”, Energy Conversion and Management, Vol. 58, 76–83, 2012.
  • Erturk, M., “Optimum insulation thicknesses of pipes with respect to different insulation materials, fuels and climate zones in Turkey”, Energy, Vol. 113, 991–1003, 2016.
  • Holman, J.P., Heat transfer, 7th ed., McGraw-Hill Book Co., New York, USA, 1992.
  • Ashrae, Handbook-Fundamentals, “Heat transfer”, Atlanta: ASHRAE, Chapter 22, p. 22.1–22.21, 1989.
Birincil Dil en
Konular Mühendislik
Dergi Bölümü Makaleler
Yazarlar

Orcid: 0000-0002-9668-6654
Yazar: Yusuf Başoğul (Sorumlu Yazar)
Kurum: ADIYAMAN ÜNİVERSİTESİ, MÜHENDİSLİK FAKÜLTESİ
Ülke: Turkey


Bibtex @araştırma makalesi { muglajsci422979, journal = {Mugla Journal of Science and Technology}, issn = {2149-3596}, address = {Mugla Sitki Kocman University}, year = {2018}, volume = {4}, pages = {89 - 101}, doi = {10.22531/muglajsci.422979}, title = {LIFE CYCLE COST ANALYSIS IN DETERMINING OPTIMUM PIPE INSULATION THICKNESS WITH AIR GAP FOR DIFFERENT CLIMATE CONDITIONS}, key = {cite}, author = {Başoğul, Yusuf} }
APA Başoğul, Y . (2018). LIFE CYCLE COST ANALYSIS IN DETERMINING OPTIMUM PIPE INSULATION THICKNESS WITH AIR GAP FOR DIFFERENT CLIMATE CONDITIONS. Mugla Journal of Science and Technology, 4 (1), 89-101. DOI: 10.22531/muglajsci.422979
MLA Başoğul, Y . "LIFE CYCLE COST ANALYSIS IN DETERMINING OPTIMUM PIPE INSULATION THICKNESS WITH AIR GAP FOR DIFFERENT CLIMATE CONDITIONS". Mugla Journal of Science and Technology 4 (2018): 89-101 <http://dergipark.gov.tr/muglajsci/issue/37235/422979>
Chicago Başoğul, Y . "LIFE CYCLE COST ANALYSIS IN DETERMINING OPTIMUM PIPE INSULATION THICKNESS WITH AIR GAP FOR DIFFERENT CLIMATE CONDITIONS". Mugla Journal of Science and Technology 4 (2018): 89-101
RIS TY - JOUR T1 - LIFE CYCLE COST ANALYSIS IN DETERMINING OPTIMUM PIPE INSULATION THICKNESS WITH AIR GAP FOR DIFFERENT CLIMATE CONDITIONS AU - Yusuf Başoğul Y1 - 2018 PY - 2018 N1 - doi: 10.22531/muglajsci.422979 DO - 10.22531/muglajsci.422979 T2 - Mugla Journal of Science and Technology JF - Journal JO - JOR SP - 89 EP - 101 VL - 4 IS - 1 SN - 2149-3596- M3 - doi: 10.22531/muglajsci.422979 UR - http://dx.doi.org/10.22531/muglajsci.422979 Y2 - 2018 ER -
EndNote %0 Mugla Journal of Science and Technology LIFE CYCLE COST ANALYSIS IN DETERMINING OPTIMUM PIPE INSULATION THICKNESS WITH AIR GAP FOR DIFFERENT CLIMATE CONDITIONS %A Yusuf Başoğul %T LIFE CYCLE COST ANALYSIS IN DETERMINING OPTIMUM PIPE INSULATION THICKNESS WITH AIR GAP FOR DIFFERENT CLIMATE CONDITIONS %D 2018 %J Mugla Journal of Science and Technology %P 2149-3596- %V 4 %N 1 %R doi: 10.22531/muglajsci.422979 %U 10.22531/muglajsci.422979
ISNAD Başoğul, Yusuf . "FARKLI İKLİM ŞARTLARI İÇİN HAVA BOŞLUKLU OPTİMUM BORU YALITIM KALINLIĞININ BELİRLENMESİNDE YAŞAM DÖNGÜSÜ MALİYET ANALİZİ". Mugla Journal of Science and Technology 4 / 1 (Haziran 2018): 89-101. http://dx.doi.org/10.22531/muglajsci.422979